Search result for:  i

@rzhang yes, i extracted the config file and replaced the older config file. it worked for few days. now the expire trial warning is back

To make MagLog software compatible with Windows11 OS, follow the steps below: 1. Download and unzip the file below to your local computer. Attachment : MagLog2017.zip 2. Make sure the installed MagLog program is not running. if it is running in the background you will need to go to the task manager and manually close the program by selecting end task. For those that may have used to compatibility work around, revert back to default by unclicking Compatibility mode in the Properties>Compatibility menu of the MagLog software. 3. Navigate to th ...

Hi Rui Working now. My fault was i scrolled up to Andre's post and read it as yours (which it is not) and it shows as "-- attachment is not available --"Now i have scrolled to the TOP and your links work. Please feel free to delete these 2 posts of mine as cured due user error

@georesults Hi Peter, i just downloaded the 2 zip files from the first post without any issue. i will investigate a little bit more.

Hi Rui Your above attachements are not working "-- attachment is not available --"

@andreyudhistika Did you download the latest configuration file, which is in a separate link, as well?

hi, i have downloaded the .exe file. when i ran it, it showed 'trial expired' do you have new version available or new trial? thank you

... observe LED on the “READY”. it takes around 1-2 second after pressing “ARM”. _____________”READY” LED on around 1-2 second after pressing “ARM” switch. Make sure wearing safety glasses to protect your eyes for next test. _____________Wear safety glasses. Press “FIRE” button while pressing “ARM” switch. Observe dummy led cap sparks and “READY” LED off, and trigger the Seismic unit. _____________Dummy led blasting cap sparks ______________”READY” LED off. ______________Trigger the Seismic unit After firing the cap, “READY” LED lit on again within 5 seconds ...

Verify BAUD Rate selected on dip switches 6,7,8 Note: according to a customer this is how the switches are set as they are attempting a file transfer at 115200 BAUD. Connect the G-857 to the computer using the download cable and a properly installed USB/RS-232 adaptor. (Must have FTDI): Open the MagMap Software. Select import>G-857/ASCII 1. Enter known Serial Port (My computer is COM4) 2. BAUD 115200 (Switches 6, 7 and 8 off) 3. Set a good location for the file to written to. 4. Leave Download only, open later unchecked. 5. Leave download ...

MagStation, the new MFAM magnetometer base station is available. it's Geometrics’ latest and most advanced magnetometer base station, designed for high-sensitivity, stationary monitoring of the Earth’s total magnetic field. Please see the product page for details. MagStation Magnetometer Base Station

The answer is NO. MagArrow or MagEx operate in the so-called combined sensor mode. The single reading is NOT the averaged reading from the 2 sensors inside. instead, the signals from the 2 sensors are combined and then data processed to produce one reading. To us, there is no point to produce 2 readings if 2 sensors are right next to each other. We are open to discussions!

@rzhangSadly no, still cant get it to detect the SD :/

@yago1212 Hi Charles, any update on the SD card issue?

Customer had problem connecting Wi-Fi using domain magarrow.net. Solution: Verify the blinking LED patterns are ok: 1) One steady blink and a pause, about once per second - The MagArrow is ready for a WIFI connection from your device. 2) Two short blinks followed by a pause – A device is connected to the MagArrow’s WIFI. if your device or another nearby device is set to connect automatically, this two-blink pattern might commence quite soon after power-on. if the MagArrow LED blinks normally, please try to connect to 192.168.1.1, instead of magarrow.net. ...

@rzhangThanks for the reply!Yes, i feel the spring, and remember the sensor was working a cuple months ago...I just tried to gently clean the SD socket, and also formated the SD - the MagArrow still doesnt seem to recognize any SD 😥 i can't think of any past sensor usage that may be related to this... im at a loss, anyone has more wisdom on the subject?