Search result for:  id10=WA 0821 7001 0763 (FORTRESS) pintu baja 100 x 240 Limbangan Kabupaten Kendal Jawa Tengah

The batteries used in the portable magnetometer instruments are lead-acid gelled electrolyte batteries. The choice of this type of battery was dictated by their non-magnetic internal construction. We “magnetically compensate” these batteries to further reduce their magnetic signature. We do this with bucking coils which are mounted against the battery surfaces and then an external wrap applied. The batteries should be charged using the charger furnished with the instrument. These chargers are fully automatic and designed to do the best job of charging and maintaining the batteries for long life. All of the chargers are equipped with lights indicating when the battery is being charged and when the charging cycle is completed. The battery packs will provide the most operating cycles when they are fully charged after each use. The number of operating cycles can vary from 250 cycles to above 1000 cycles depending on how deep the discharge was and how soon the battery is charged after use. A 30% discharge per cycle may result in a lifetime of 1000 cycles or more, whereas a 100% discharge per cycle can result in only 250 cycles. As a rule the magnetometer will shut down when the battery is discharged to about 20% of full voltage. This is to ensure proper shutdown of the instrument. It is very important to recharge the battery as soon as possible after use so the maximum life can be expected from the pack. If the discharged pack is left to charge “when we get back from the field” the pack can suffer from “sulphation”. This is a high-resistance buildup in the battery which may render the battery unusable. If a battery of this type must be stored for an extended period, it must be stored in a fully-charged condition. If such a battery is stored discharged and subject to below-freezing conditions, it is likely to freeze and be subsequently unusable. All Lead-Acid batteries must be maintained when in storage. This means that the user must recharge each pack at least once a month. Lead Acid batteries will self-discharge due to stray internal resistances, causing very small drain currents. Thus the maintenance requirement for monthly recharging is critical to long battery life. Do not leave the charger on all the time during storage. Also it is very important to use discharge the batteries on a regular basis otherwise the lifespan will be severely shortened. For more information contact our Support Department.

The subject of "Bandwidth" comes up often when discussing cesium magnetometers. There are two different aspects of bandwidth that are different and need to be differentiated: The cesium magnetometer uses an atomic resonance of the Cs 133 atom (see note 1 below) which varies proportional to the ambient magnetic field. This atomic resonance is used to set/control the frequency of an oscillator. Therefore the output signal from the magnetometer is a *frequency* which is proportional to the earth's magnetic field at a coefficient of 3.498572 Hertz per nT. Thus the output frequency (called the Larmor frequency) varies from roughly 70KHz at the equator to 350 KHz at the poles. Because the cesium magnetometer is an oscillator, and because phase is important in an oscillator, the "Bandwidth" of the electronics in the magnetometer must be at least 10 times higher than the maximum output frequency of 350 Khz, or roughly 3.5 MHz. This bandwidth should not be confused with the magnetic field measurement "Bandwidth", or how fast of a magnetic field change can be measured. To put a scaler value on any magnetic field reading the output frequency of the magnetometer must be counted, and then scaled appropriately to get a field reading in nanoTeslas. The counting process involves opening a gate period, counting the number of Larmor (frequency) cycles that occur, divide that number by the precise time interval of the gate period. then scale that value by dividing by the 3.498572 Hz / Larmor coefficient. You get one reading per gate period, which by default is five or ten hertz (200mS to 100 mS gate period). What you get for a reading during any gate period is the time interval average of the Larmor frequency over that period. The transfer function of a "time interval averaged" signal is [sine(x) / x] with the first zero falling at the sample frequency. Thus if the G-882 is sampling at 10 hertz the maximum resolvable magnetic field change is roughly 5 hertz. The sample interval of the G-882 is adjustable by sending commands to it. If the sample rate is set to 20 hertz the measurement bandwidth will double (from a 10 hertz sample rate) but the base line noise will go up as well. It should also be noted that the basic system noise level of the G-882 for a stationary sensor is set by the counter resolution - not by the signal to noise ratio of the oscillator electronics. If the sensor is tilted away from its optimum orientation the magnetometer signal will decrease (and therefore the signal to noise ratio), but the counted field output will not show any significant degradation until the sensor is approaching the dead zone (where the signal is really low).

Raw Data MagArrow data is imported into Survey Manager in the form of .MAGDATA files, downloaded from the MagArrow. The .MAGDATA file contains measurements from different sensors inside the MagArrow: 1000Hz magnetometer readings; accelerometer, gyro, compass, temperature readings; and GPS info. MFAM assigns a fiducial number, or “FID” to each magnetometer reading, in a cycle from 1 to 1000 that repeats every second. In the instrument, the magnetometer readings and the GPS sentence data are synchronized so that the “FID-1” magnetometer record is matched with the GPS location and timing information. Exports to CSV and Geosoft file formats 1000Hz un-filtered export The 1000Hz export provides the original raw magnetometer data plus some simple interpolations: • Magnetometer reading: The raw magnetic field values are exported without application of a filter. [While these raw measurements are the output of a filter inside the MFAM sensor: a 9-pole Butterworth low pass filter with a -3dB point at 400Hz, that filter is considered part of the sensor for this description.] • Auxiliary sensors: Gyro, accelerometer, and temperature are acquired once per every 5 magnetometer readings, and are reported only when acquired. Compass readings are acquired one per every 10 magnetometer readings and are reported only when acquired. • GPS NMEA sentence: Reported with the associated FID-1 mag record. A few individual fields from the GPS are also broken out from the GPS sentence and reported separately, without interpolation. • Interpolated GPS fields: Time, date, latitude, longitude, and track (course over ground) are linearly interpolated between GPS readings. Decimated exports Each of the exports at frequencies from 10 Hz to 100 Hz is a decimation – data are filtered by a low-pass filter and then down-sampled to the target sample rate. Each low-pass filter (a different one for each decimation) is a symmetric finite impulse response (or FIR) filter, with the following design goals: • -3dB attenuation at 0.75 * Nyquist frequency (e.g., the -3dB point for the 10Hz decimation is 3.75Hz) • Significant attenuation of 50Hz and 60Hz signals. • Reasonably flat response in the pass band. Linear phase (or zero phase, or constant group delay) filters. These filters are not Kalman filters. The filters are applied to fields in the decimations as follows: • Magnetometer readings: Magnetometer readings are decimated: the FIR is applied, then the data are down-sampled to the target rate. • Aux sensors: Aux sensors are first up-sampled to 1000Hz by linear interpolation of values between individual readings (which occur once every 5 mag readings for gyro, accelerometer, and temperature, and once every 10 mag readings for compass). Then these 1000Hz values are decimated in the same process as the magnetometer readings. • Latitude and longitude are first up-sampled to 1000Hz by linear interpolation of values between successive GPS data (once per second), then these 1000 Hz values are decimated in the same process as the magnetometer readings. • Time, date, and track are linearly interpolated as in the raw, unfiltered 1000Hz export. Merging filtered and unfiltered data. Some of the values in an individual line of data are filtered: mag readings, aux sensors, etc. Other measurements are not filtered: time and date, GPS sentences, record counters, and the simple interpolated fields. These two sets of values – filtered and unfiltered, must be reported in individual lines that contain values of both types. The question “How should the two sets of values be matched?” is addressed as follows: A decimation filter has a center. For example, a single filter result that weighs 499 individual measurements running from record number 752 to record number 1250 (in DSP terms, it is the result of the convolution of 499 input values with 499 filter weights), is centered on record number 1001. The result is the “filtered value of record 1001”. In a single line along with this value should be the other filtered results centered on record number 1001 plus the unfiltered raw and interpolated values that were recorded as part of the original, raw record 1001. The down-sampling part of decimation involves keeping some results and discarding others; down-sampling from 1000Hz to 100Hz includes discarding 9 out of 10 results. During exports, Survey Manager keeps the “FID 1” record, because it includes the original GPS information, then discards the next 9 records (if it’s a 100Hz decimation), and then repeats the pattern, each time starting with FID 1. If you have questions about the MagArrow decimations, please contact your Geometrics account manager.

Total field magnetometers like the optically pumped cesium magnetometer are passive devices, they do not send out waves or pulses. They measure distortions in the earth’s normally homogenous magnetic field and can sense distortions due to ferrous objects at great distances. The basic rule of thumb is that one ton (1000 Kg) of steel or iron will give us a 1nT anomaly at 100 ft. or 30m. Since the amount of distortion falls off as the cube with distance (compare a metal detector which falls off as the inverse 6th power!) and is linear with mass, every time we cut the distance in half, we can see 1/8th the mass. Therefore, we can sense 250 lbs. (100kg) at 50 feet (15m), or 30lbs (15kg) at 25 feet (8m), or 4lbs (2kg) at 12 feet (4m). However this is not the whole story. The factors given above are for induced magnetic fields only. Many targets also have remnant or permanent magnetic effects (meaning they have become magnetized either in production or by the earth’s field) and can therefore have larger anomalies by a factor of 3 or 5 or more. Also many hollow objects like barrels or other tubular structures appear as though they are solid due to self-shielding from the earth’s field, and thus have much larger anomalies than their mass would predict alone. Pipes fall off as the inverse square and are thus detectable at even greater distances. Please see our Applications Manual for Portable Magnetometers for more information.

The subject of "Bandwidth" comes up often when discussing cesium magnetometers. There are two different aspects of bandwidth that are different and need to be differentiated: The cesium magnetometer uses an atomic resonance of the Cs 133 atom (see note 1 below) which varies proportional to the ambient magnetic field. This atomic resonance is used to set/control the frequency of an oscillator. Therefore the output signal from the magnetometer is a *frequency* which is proportional to the earth's magnetic field at a coefficient of 3.498572 Hertz per nT. Thus the output frequency (called the Larmor frequency) varies from roughly 70KHz at the equator to 350 KHz at the poles. Because the cesium magnetometer is an oscillator, and because phase is important in an oscillator, the "Bandwidth" of the electronics in the magnetometer must be at least 10 times higher than the maximum output frequency of 350 Khz, or roughly 3.5 MHz. This bandwidth should not be confused with the magnetic field measurement "Bandwidth", or how fast of a magnetic field change can be measured. To put a scaler value on any magnetic field reading the output frequency of the magnetometer must be counted, and then scaled appropriately to get a field reading in nanoTeslas. The counting process involves opening a gate period, counting the number of Larmor (frequency) cycles that occur, divide that number by the precise time interval of the gate period. then scale that value by dividing by the 3.498572 Hz / Larmor coefficient. You get one reading per gate period, which by default is five or ten hertz (200mS to 100 mS gate period). What you get for a reading during any gate period is the time interval average of the Larmor frequency over that period. The transfer function of a "time interval averaged" signal is [sine(x) / x] with the first zero falling at the sample frequency. Thus if the G-882 is sampling at 10 hertz the maximum resolvable magnetic field change is roughly 5 hertz. The sample interval of the G-882 is adjustable by sending commands to it. If the sample rate is set to 20 hertz the measurement bandwidth will double (from a 10 hertz sample rate) but the base line noise will go up as well. It should also be noted that the basic system noise level of the G-882 for a stationary sensor is set by the counter resolution - not by the signal to noise ratio of the oscillator electronics. If the sensor is tilted away from its optimum orientation the magnetometer signal will decrease (and therefore the signal to noise ratio), but the counted field output will not show any significant degradation until the sensor is approaching the dead zone (where the signal is really low).